RMS 560

Recessed luminaire for rooms with chemical agents and gases with IP66 protection rating.
Ex n ed11c T4 explosion-proof protection with electronic transformer.


ask for a quote

Size Chart
alt
CLOTHES
MEASUREXS/34S/36M/38-40L/40-42
UK681012
USA46810
FRA36384042
Waist (cm)64687276
Chest (cm)81858993
Seat (cm)899397101
Inseam (cm)81828384



SHOES
FOOT IN INCHESFOOT IN CMUSAEuroUK
9¼23.56395
9½24.16.539.55.5
9¾24.87.5406
1025.48417
10¼25.78.541.57.5
10½269428
10¾27.39.542.59.5
CLOTHES
MEASUREXS/34S/36M/38-40L/40-42
UK681012
USA46810
FRA36384042
Waist (cm)64687276
Chest (cm)81858993
Seat (cm)899397101
Inseam (cm)81828384



SHOES
FOOT IN INCHESFOOT IN CMUSAEuroUK
9¼23.56395
9½24.16.539.55.5
9¾24.87.5406
1025.48417
10¼25.78.541.57.5
10½269428
10¾27.39.542.59.5

How to Take Clothing Measurements

  1. Get a flexible measuring tape. These are often sold in craft stores
  2. Neck:
    • Measure around the base of the neck in inches.
    • Round up to the nearest half inch.
  3. Chest:
    • Wrap tape measure under armpits around fullest part of chest (usually right above nipples
  4. Sleeve:
    • Bend your elbow and rest your hand on your hip.
    • Have someone measure from the middle of the back of your neck to your wrist by putting the tape measure over your shoulder, around your elbow and to your wrist.
  5. Waist:
    • Wrap tape measure around where you normally wear your pants. Keep tape measure a little loose by keeping a finger between the tape measure and your waist.
  6. Inseam:
    • Put on a pair of shoes.Have someone measure from your crotch to back of the heel, where you want your pants to end.
  7. Hands:
    • Measure around the hand at the fullest part (exclude thumb). The number of inches shows the size of the glove.
Quantity

Add to favorites
You must be logged in
Add to wishlist
You must be logged in
BODY

In stainless steel AISI-304 thickness 0,8 mm. Obtained by deep-drowing stamp in one block without weldings.

ELECTRIC WIRING

Homologated with HF electronic ballast. High thermal resistance unipolar cables, terminal with fuse. Reflecting fillet inside AISI-304 device.

DIFFUSER

AISI-304 stainless steel frame, thickness 1 mm. Obtained by die and shear in block without weldings. Body-frame closing system by hinge with TCEI stainless steel AISI-304 screws. Optic space in 4 mm. temperated glass. It is fixed to the frame by silicone weld.

POWER

Technical note

It is possible have personalized internal wiring in according to laws INERIS 01 ATEX 0060

Explosion - Proof protection

Ex-n-ed11CT4-IP65

Normative:

EN60079-0, EN60079-1, EN60079-7,
EN60079-5 EN61241-0, EN61241-1,
IEC60079-0, 60079-1, 60079-7, 61241-0, 62141-1
Radiofrequences ed EMC
SEC. DIR. 89/336 CE
ATEX Directive 2014/34/EU

* All our lighting products are covered by Civil-Insurance products responsability.

No customer reviews for the moment.

Write your review